[Metal Claw QI] A smartphone holder made entirely of aluminum alloy. You can attach and detach your smartphone by pushing up the upper arm with your smartphone. By adjusting the height of the lower arm, you can adjust the wireless charging position to suit your smartphone model. The claw can be adjusted in 6 steps from 13 to 18 mm to suit the thickness of your smartphone. Guide arms on both sides make it easy to aim at the center and prevent sideways slipping. The arm can be fixed using the dial on the back to prevent the arm from opening due to impact while driving. The standard vibration absorption damper efficiently absorbs high frequencies caused by engine vibration, reducing the risk of damage to the image stabilization function of your smartphone camera. ``I'm worried about plastic deterioration'' ``I want a sturdy aluminum holder'' ``I like a holder that has a metallic feel that doesn't overlap with the surroundings'' ``I want a QI compatible holder'' This is the model KDR- recommended for those people. It's M23A. [Compatible reference models] iPhone 15 / 15Pro / 15Pro Max / 15Plus / 14 / 14Plus / 14Pro / 14Pro max / 13 Pro Max / iPhone 13 Pro / 13 / 13mini / 12 Pro / 12 / 12 Pro Max / 12mini / SE 3 / SE 2 / 11 / 11Pro / 11Pro Max / X / XS / XR / XS Max / 8 / 8 Plus / Samsung Galaxy / Google Pixel / Kyocera Torque / Sony Xperia / Sharp Aquos and other QI compatible models *Smartphone accessories such as cases Please check the actual size including the conditions. Compliance with hold and charge; camera exposure is not included. ■Height: 125-180mm, Width: 63-90mm (Please check if the size of your smartphone is within the range.) ■Thickness: 18mm or less (Please be careful about thick smartphone models and cases.), ■Smartphone cases, bunker rings, etc. It has excellent compatibility as it can handle thicknesses up to 18mm without affecting the thickness. ■If the smartphone case contains metal or magnetism, it will be detected and a protection will be activated and stopped for safety. If your smartphone case is thick, the distance of wireless charging will be insufficient and the battery will not be charged. ■We recommend that you prepare for unexpected situations by using the KDR-SFB-S safety strap or carabiner, and connecting it to the handle after setting the holder. [QI Charging] QI wireless charging is possible with two input methods: vehicle 12V and USB (QC3.0). ■Output: QI15W/10W/7.5W/5W *Charged with the power requested by the model. ■12V input: Wireless charging can be used by connecting to the vehicle's 12V power supply. *Cannot be used with batteryless cars, 6V, 24V battery cars. ■USB input: Wireless charging is possible by connecting to a USB power supply QC3.0 *Body connector type A. The power to the mobile battery may be cut off due to power consumption control. Do not get the USB connector wet in rainy weather. ■Waterproof: IP66 waterproof and can withstand sudden rain. ■Power switch: ON/OFF only. When 12V is received from 0V, the power will automatically turn on. ■12V wiring: 1.75m inconspicuous black double cord (line with white text on the positive side), (with fuse holder, bullet, convertible to stag terminal) ■USB wiring: 1.2m inconspicuous black double cord (white line on the positive side) (Character line) ■Note: If you do not understand voltage drop (including contractors), please wire the negative wire directly to the battery negative terminal. Body grounding can only be used if the resistance value between the battery negative terminal and the grounding point is confirmed to be 0Ω.Do not connect the grounding at points where the resistance value is unstable, such as the handle. Please also be careful about voltage drop due to reduced contact area of ​​crimp terminals. *The voltage of the ground resistance is normal when no load is applied, but the voltage drops when a load is applied. To check the power supply, be sure to measure the load voltage under the following conditions. (Measure with the wiring connected and the circuit established, the power switch on the smartphone holder turned on, and applying the probe to the SAE connector with a gap) *No-load voltage measurement does not determine the quality of the power supply. [Product specifications] ■Holder size: Height 125-180mm, width 63-90mm, thickness

[Metal Claw QI] A smartphone holder made entirely of aluminum alloy. You can attach and detach your smartphone by pushing up the upper arm with your smartphone. By adjusting the height of the lower arm, you can adjust the wireless charging position to suit your smartphone model. The claw can be adjusted in 6 steps from 13 to 18 mm to suit the thickness of your smartphone. Guide arms on both sides make it easy to aim at the center and prevent sideways slipping. The arm can be fixed using the dial on the back to prevent the arm from opening due to impact while driving. The standard vibration absorption damper efficiently absorbs high frequencies caused by engine vibration, reducing the risk of damage to the image stabilization function of your smartphone camera. ``I'm worried about plastic deterioration'' ``I want a sturdy aluminum holder'' ``I like a holder that has a metallic feel that doesn't overlap with the surroundings'' ``I want a QI compatible holder'' This is the model KDR- recommended for those people. It's M23A.